Haws Polar Series Skid Mounted Tempering Water System w/ Heater TWBS, SH
Haws 8780 Polar Series Skid Mounted Tempering System
Haws Model 8780 Polar series is a skid-mounted tempering system that comes equipped with a water heater, mixing valve, and holding tank. Skid is a water resistant, polyurea membrane-encased, steel-reinforced wooden structure. Haws systems have multiple levels of back-up protection to ensure uninterrupted flow with anti-scald protection and full flow cold water bypass. These systems may supply a number of drench systems or eyewash stations, and are for use in indoor areas that are protected from freezing. Feeder lines should be heat-traced, or a recirculating pump used.The Haws Model 8780 is available with either a 119 or a 325 gallon storage capacity tank, as well as an instantaneous steam heat exchanger as options. Should the simultaneous operation of more than one shower be desired, Haws offers a high-flow blending system for the 325 gallon tank and steam heat exchanger systems. Specifications
Blending System: Model TWBS.SH.
Water Heater: 4 KW, 240 VAC copper immersion heater or steam heat exchanger.
Thermostat: Dual element thermostat with manual reset hi-limit protection.
Skid: 4' x 5' water resistant , polyurea membrane-encased, steel reinforced wooden structure.
Plumbing
Schedule 40 galvanized piping with brass and stainless steel valves.
Supply: 1-1/4" IPS. Tempering System Options:
Tank Systems
Option No. 21: 119 gallon tank: Stores enough hot water to provide a single 20 gpm shower for 15 minutes. Recovery time of up to 4 hours.
Option No. 22: 119 gallon ASME tank: Stores enough hot water to provide a single 20 gpm shower for 15 minutes. Recovery time of up to 4 hours.
Option No. 23: 325 gallon ASME tank: Stores enough hot water to provide two 20 gpm showers for 15 minutes. Recovery time of up to 11 hours. Tank is insulated and jacketed.
Steam Systems
When a steam supply is available, a Haws steam heat exchanger and mixing system is the best approach for efficient tempering, especially with multiple shower or recirculating systems. Standard steam system is sized to provide up to 35 gpm of 80°F (26°C) tempered water, and require no recovery time. Higher flow systems are available.
Option No. 24: Steam heat exchanger, feed forward instantaneous heat exchanger. Requires 15 psig, max. 1300 lb./hr steam supply. Electrical System Options
Standard system requires 208-240 VAC single phase, 2 wire and ground, 20 amp electrical supply. Electrical systems can be provided to meet various environmental requirements. Select the electrical option that meets the environmental conditions where the Polar unit is to be installed.
Option No. 31: NEMA 4 water/dust tight when tank tempering system is selected.
Option No. 32: Class I, Division 2, Group B, C, Dand T4.
Option No. 33: Class I, Division 1, Group C, Dand T4. Specify Polar model as follows: Model number, tempering system option, and electrical system option. Example: Model 8780.22.32 is a Model 8780 equipped with a 119 ASME tank, Class I, Division 2, Groups B, C, D and T4 electrical system.
8780.21.31 shown. For the enclosed version
First Aid and Safety Online was developed as your single source for all of your first aid and safety supply requirements. The Polar Booth Emergency Shower Units by Haws Company offered here have been selected for our online store for their superior quality and value. We are your first aid source for maintaining compliance with OSHA regulations. With First Aid and Safety Online, you will never run out of needed first aid supplies to treat workplace injuries. Should you need a first aid or safety product not found in our online store, please contact our office (800 506-0091) and we will be happy to assist you in fulfilling your order.